A 5 V Arduino UNO R3 compatible board built on the ATmega328P, ready for sketches, shields and everyday Arduino IDE projects.
The Arduino UNO R3 Compatible board is a development board based on the ATmega328P 8-bit AVR microcontroller, with 14 digital I/O pins, 6 analog inputs and a USB Type-B port for programming. It suits beginners learning electronics and makers who want a low-cost board that runs standard Arduino UNO sketches.
Microcontroller
ATmega328P
Logic level
5 V
I/O
14 digital (6 PWM) + 6 analog
USB
Type-B
Why choose it
Runs standard UNO sketches — it uses the same ATmega328P as the Arduino UNO R3, so you select Arduino Uno in the Arduino IDE.
Plenty of pins for first projects — 14 digital I/O pins (6 with PWM) and 6 analog inputs, all at 5 V logic, which matches most hobby sensors and modules.
Program it over USB — upload from the Arduino IDE through the USB Type-B port; no separate programmer is needed.
Specifications
Core
Microcontroller
ATmega328P (8-bit AVR)
Clock speed
16 MHz
Flash memory
32 KB
SRAM
2 KB
EEPROM
1 KB
Power
Logic level
5 V
Input voltage (DC jack / VIN), recommended
7–12 V
Input voltage, absolute maximum
20 V
USB power
5 V from the USB port
Inputs and outputs
Digital I/O pins
14 (D0–D13)
PWM outputs
6 (D3, D5, D6, D9, D10, D11)
Analog inputs
6 (A0–A5), 10-bit ADC
Current per I/O pin
20 mA recommended maximum (40 mA absolute maximum)
3.3 V-only devices (ESP32, ESP8266, Raspberry Pi and Pico GPIO)
◐ With adapter
The UNO outputs 5 V. Use a level shifter before a 3.3 V input.
In the box
Included
1 × Arduino UNO R3 compatible board (ATmega328P)
1 × 40-pin single-row male straight pin header strip
Applications
Learning electronics and programming with LEDs, buttons and sensors
Reading sensors and printing values to the Serial Monitor
Controlling servos, relays and displays through UNO R3 shields and modules
Prototyping 5 V projects before moving to a custom PCB
Tutorial
What you'll build: set up the Arduino IDE, upload your first sketch to blink the on-board LED, then fade an LED on a breadboard. About 30 minutes.
Part 1 — Set up your computer (once only)
1
Install the Arduino IDE Download the free Arduino IDE for your computer from arduino.cc/en/software and run the installer. Open the IDE when it finishes.
2
Connect the board Plug a USB data cable into the square USB Type-B port on the board and into your computer. Use a data cable, because some cables only charge. If you need one, see the USB cable for Arduino UNO.
3
Check the port (only if needed) Open Tools → Port in the Arduino IDE. If no new port appears, swap to a USB data cable (some cables are charge-only), then unplug and re-plug the board.
✓ Check: Tools → Port shows a new port, for example COM3 on Windows.
Part 2 — Upload your first sketch
4
Choose the board and port In the Arduino IDE, choose Tools → Board → Arduino AVR Boards → Arduino Uno. Then choose the new port under Tools → Port.
5
Paste the sketch and upload Click File → New Sketch, delete the template, paste Example 1 below, then click the Upload button (the right-pointing arrow). Wait for “Done uploading”.
▸ Example 1 — Blink the on-board LED
// Example 1 - Blink the on-board LED
// Wiring: none (USB cable only)
const int LED_PIN = LED_BUILTIN; // pin 13 on the UNO - you can change this
void setup() {
pinMode(LED_PIN, OUTPUT); // make the LED pin an output
Serial.begin(9600); // speed for the Serial Monitor
Serial.println("OK - epartners.co.nz test");
}
void loop() {
digitalWrite(LED_PIN, HIGH); // LED on
Serial.println("LED on");
delay(1000); // wait 1 second - you can change this
digitalWrite(LED_PIN, LOW); // LED off
Serial.println("LED off");
delay(1000);
}
✓ Check: The on-board LED (usually marked L) blinks once a second. Open Tools → Serial Monitor, set 9600 baud, and you will see “OK - epartners.co.nz test” followed by “LED on” and “LED off”.
■ Power ■ GND ■ Signal ■ I2C / SPI / UART ■ Other ⌒ = wires cross, not connected
#
Arduino UNO pin
Connects to
Wire
Notes
1
D9
220 Ω resistor, first leg
Yellow
D9 is a PWM pin
2
—
220 Ω resistor, second leg → LED long leg (+)
Yellow
The resistor can go either way round
3
GND
LED short leg (−)
Black
Every circuit needs a return path to GND
Watch out: an LED only works one way round. The long leg is +. The 220 Ω resistor keeps the current low enough for the LED and for the pin (20 mA recommended maximum per I/O pin).
6
Wire the circuit Unplug the USB cable first. Build the circuit from the diagram and table above, then plug the USB cable back in.
7
Upload Example 2 Paste Example 2 into a new sketch and click Upload. D9 is one of the 6 PWM pins, so analogWrite() can set the LED brightness from 0 (off) to 255 (full).
▸ Example 2 — Fade an LED
// Example 2 - Fade an LED with PWM
// Wiring: D9 -> 220 ohm resistor -> LED long leg (+); LED short leg (-) -> GND
const int LED_PIN = 9; // PWM pin, matches the pin table
int brightness = 0; // current brightness, 0-255
int stepSize = 5; // how fast it fades - you can change this
void setup() {
pinMode(LED_PIN, OUTPUT);
Serial.begin(9600);
Serial.println("OK - epartners.co.nz test");
}
void loop() {
analogWrite(LED_PIN, brightness); // set the brightness
brightness += stepSize; // move up or down
if (brightness <= 0 || brightness >= 255) {
stepSize = -stepSize; // turn around at the ends
}
delay(30); // pause between steps - you can change this
}
✓ Check: The LED slowly brightens and dims, again and again. The Serial Monitor (9600 baud) shows “OK - epartners.co.nz test” once.
Troubleshooting
Problem
Likely cause
Fix
No port appears under Tools → Port
Charge-only USB cable
Try a USB data cable and re-plug the board
Upload fails with “not in sync”
Wrong board or port selected, or something is connected to D0 or D1
Choose Arduino Uno and the correct port, and disconnect anything from D0 and D1 during upload
Example 2 LED stays off
LED the wrong way round, or a loose wire
Swap the LED legs (long leg to the resistor side) and check each wire
Serial Monitor shows odd characters
Baud rate does not match
Set the Serial Monitor to 9600 baud
Try next: add a push button on another pin and use it to turn the LED on and off.
Spotted a problem in this tutorial? Email support@epartners.co.nz and we'll check it and update the tutorial.
Good to know
The I/O pins are 5 V. Do not connect 5 V outputs to 3.3 V-only devices (ESP32, ESP8266, Raspberry Pi) without a level shifter.
Power the board from USB, or from 7–12 V DC on the DC jack or VIN pin (20 V is the absolute maximum). The official UNO R3 pinout lists a 50 mA maximum on the 3.3 V pin.
D0 and D1 are shared with USB serial. Disconnect anything on D0 and D1 while uploading, and do not draw more than 20 mA from a single I/O pin.
Datasheet
Key figures from the manufacturer's datasheet for the ATmega328P, the microcontroller on this board, which runs it at 5 V and 16 MHz.
ATmega328P microcontroller
Core
8-bit AVR microcontroller
Flash memory
32 KB
SRAM
2 KB
EEPROM
1 KB
Operating voltage
1.8–5.5 V
Maximum frequency
20 MHz at 4.5–5.5 V (10 MHz at 2.7–5.5 V, 4 MHz at 1.8–5.5 V)
ATmega32U4 with native USB, so it can appear as a keyboard or mouse; 2.5 KB SRAM
Projects that need USB keyboard or mouse emulation
FAQ
▸ Can I program it in the Arduino IDE as an Arduino Uno?
Yes. Choose Tools → Board → Arduino AVR Boards → Arduino Uno, pick the port, and upload as normal.
▸ Is the board 5 V or 3.3 V?
It uses 5 V logic. Connect 3.3 V-only devices through a level shifter.
▸ How do I power it?
Use the USB port, or 7–12 V DC on the DC jack or VIN pin. 20 V is the absolute maximum.
▸ Why does my computer not show a port?
Use a USB data cable first. If the port is still missing, re-plug the board and check Tools → Port again.
Technical question about this part? Email support@epartners.co.nz with your board and wiring, and we'll help you get it working.
Shipping: $5.99 urban, $9.99 rural. Free shipping on orders of $100 or more.
Order by 10:30am (NZT), Monday to Friday, and we dispatch the same day. Orders placed after 10:30am, on weekends or on public holidays are dispatched the next business day.
Delivery usually takes 1–2 business days after dispatch (2–3 for rural addresses). See our Shipping Policy for full details.