ESP32-S3 N16R8 Development Board with Antenna - Not Assembled

SKU: SW5007
ESP32-S3 N16R8 development board with two pin header strips and a 2.4 GHz antenna with cable, top view
ESP32-S3 N16R8 board front view with labelled module, RGB LED, RST and BOOT buttons and two USB-C ports
ESP32-S3 N16R8 board measuring 57 mm by 28 mm with pin labels along both edges
ESP32-S3 N16R8 pinout diagram showing GPIO, ADC, touch and power pin functions

ESP32-S3 N16R8 Development Board with Antenna - Not Assembled

SKU: SW5007
Default
Regular price $24.99
/
  • Free shipping on all orders over $100
  • Secure payments
  • Low stock - 1 item left
  • Inventory on the way

Add $100.00 more for free shipping

Tax included. Shipping calculated at checkout.

You'll also need

An ESP32-S3 N16R8 development board with 16 MB flash, 8 MB PSRAM, 2.4 GHz Wi-Fi, Bluetooth 5 LE and two USB-C ports.

This board is built around the ESP32-S3 N16R8 module (ESP32-S3-WROOM-1 family): a dual-core Xtensa® LX7 processor running up to 240 MHz, with the large flash and PSRAM that bigger firmware, displays and data buffers need. It suits makers moving up from the ESP32 who want more memory and native USB, and it ships with a 2.4 GHz antenna.

Memory
16 MB flash + 8 MB PSRAM
Processor
Dual-core LX7, 240 MHz
Wireless
Wi-Fi 2.4 GHz + BLE 5
USB
2 × USB-C

Why choose it

  • Room for bigger projects — 16 MB of flash and 8 MB of Octal PSRAM, far more than a standard ESP32 module.
  • Two USB-C ports — one for programming and serial output, one for the ESP32-S3’s native USB.
  • Wi-Fi and Bluetooth 5 LE — 802.11 b/g/n at 2.4 GHz plus Bluetooth LE (including Bluetooth mesh).

Specifications

Core and memory
Core ESP32-S3 N16R8 (ESP32-S3-WROOM-1 module family)
Processor Xtensa® dual-core 32-bit LX7, up to 240 MHz
Flash 16 MB (Quad SPI)
PSRAM 8 MB (Octal SPI)
Internal memory 512 KB SRAM, 384 KB ROM, 16 KB RTC SRAM
Wireless
Wi-Fi IEEE 802.11 b/g/n, 2.4 GHz, up to 150 Mbps
Bluetooth Bluetooth LE (Bluetooth 5, Bluetooth mesh); no Classic Bluetooth
Interfaces and power
GPIOs on the module 36 (4 are strapping pins); GPIO35, GPIO36 and GPIO37 are used by the Octal PSRAM and are not available
Interfaces SPI, I2S, I2C, UART, TWAI® (CAN 2.0), SD/MMC host, LED PWM, RMT, USB 2.0 OTG full-speed, USB Serial/JTAG
Onboard 2 × USB-C ports, RGB LED, BOOT and RST buttons, power, TX and RX LEDs
Operating voltage (module) 3.0–3.6 V
Logic level 3.3 V
Operating temperature (N16R8 module) −40 °C to +65 °C
Physical
Board size 57 × 28 mm

Compatibility

Platform Works Notes
Arduino IDE ✓ Yes Install “esp32 by Espressif Systems”, then choose ESP32S3 Dev Module
ESP-IDF (Espressif) ✓ Yes Target esp32s3, see the Espressif get-started guide in Resources
5 V boards (Arduino UNO / Nano) ◐ With adapter GPIOs are 3.3 V only. Use a logic level shifter between 5 V signals and this board
Windows / macOS / Linux ✓ Yes Connects over USB-C

In the box

Included
  • 1 × ESP32-S3 N16R8 Development Board - Not Assembled
  • 2 × pin header strips
  • 1 × 2.4 GHz antenna with cable

Applications

  • Wi-Fi and Bluetooth LE sensor nodes that buffer readings in PSRAM
  • Projects that need USB device features through the native USB port
  • Prototyping firmware that is too large for a 4 MB ESP32 board

Tutorial

Part 1 — Set up the Arduino IDE (once only)

1
Install the Arduino IDE
Download and install the Arduino IDE for your computer, then open it.
2
Add the ESP32 board manager link
Open File → Preferences (Arduino IDE → Settings on macOS). In “Additional boards manager URLs”, paste https://espressif.github.io/arduino-esp32/package_esp32_index.json and click OK. See the official install guide if you get stuck.
3
Install the ESP32 boards
Open Tools → Board → Boards Manager, search for esp32, and install “esp32 by Espressif Systems”.

Part 2 — Upload your first sketch

4
Connect the board
Plug a USB-C data cable into the USB-C port that the board labels as the serial port. The other USB-C port is the ESP32-S3’s native USB (GPIO19 and GPIO20) and is not used in this tutorial.
5
Choose the board settings
Tools → Board → esp32 → ESP32S3 Dev Module. Then set Tools → Flash Size → 16MB (128Mb) and Tools → PSRAM → OPI PSRAM. Leave USB CDC On Boot on Disabled. Choose your board in Tools → Port.
6
Upload the example
Copy Example 1 below into a new sketch and click Upload. If the upload fails, set Tools → Upload Speed → 115200 and upload again.
▸ Example 1 — Chip, flash and PSRAM check
// ESP32-S3 N16R8 - first upload: print chip, flash and PSRAM details
// Board: ESP32S3 Dev Module, Flash Size 16MB (128Mb), PSRAM OPI PSRAM

void setup() {
  Serial.begin(115200);  // Serial Monitor must also be 115200 baud
  delay(1500);           // give the Serial Monitor time to connect
  Serial.println("OK - epartners.co.nz test");  // printed once
  Serial.printf("Chip model: %s, revision %u\n", ESP.getChipModel(), ESP.getChipRevision());
  Serial.printf("CPU speed: %u MHz\n", ESP.getCpuFreqMHz());
  Serial.printf("Flash size: %.1f MB\n", ESP.getFlashChipSize() / 1048576.0);
  Serial.printf("PSRAM size: %.1f MB\n", ESP.getPsramSize() / 1048576.0);
}

void loop() {
  // nothing to do here
}
7
Open the Serial Monitor
Tools → Serial Monitor, set the speed to 115200 baud, and press the RST button on the board.

✓ Check: The monitor prints “OK - epartners.co.nz test”, then the chip model (ESP32-S3), CPU speed 240 MHz, Flash size 16.0 MB and PSRAM size of about 8 MB.

Part 3 — Your first real project: a Wi-Fi scanner

The ESP32-S3 has a 2.4 GHz Wi-Fi radio. This sketch lists the networks it can hear, with signal strength (RSSI, closer to 0 dBm is stronger). It does not join any network.

8
Upload the scanner
Copy Example 2 into a new sketch, keep the same board settings, and click Upload.
▸ Example 2 — Wi-Fi network scanner
// ESP32-S3 N16R8 - scan nearby 2.4 GHz Wi-Fi networks
#include <WiFi.h>

void setup() {
  Serial.begin(115200);
  delay(1500);
  Serial.println("OK - epartners.co.nz test");  // printed once
  WiFi.STA.begin();  // station mode, no network joined (arduino-esp32 3.x)
}

void loop() {
  int n = WiFi.scanNetworks();  // blocks until the scan finishes
  if (n <= 0) {
    Serial.println("No networks found");
  } else {
    Serial.printf("%d networks found\n", n);
    for (int i = 0; i < n; i++) {
      Serial.printf("%2d: %-32.32s  RSSI %d dBm  channel %d  %s\n",
                    i + 1,
                    WiFi.SSID(i).c_str(),
                    (int)WiFi.RSSI(i),
                    (int)WiFi.channel(i),
                    WiFi.encryptionType(i) == WIFI_AUTH_OPEN ? "open" : "secured");
    }
  }
  WiFi.scanDelete();  // free the scan results
  delay(5000);        // you can change this: wait 5 seconds between scans
}

✓ Check: Every 5 seconds the Serial Monitor (115200 baud) lists nearby 2.4 GHz networks with their RSSI and channel.

Troubleshooting

Problem Likely cause Fix
Board or port does not appear in Tools → Port Cable is charge-only, or the wrong USB-C port is used Use a USB-C data cable and plug it into the USB-C port labelled as the serial port on the board. Unplug, plug in again, then reopen the Tools menu
Upload fails or stops part-way Upload speed too high for the cable Tools → Upload Speed → 115200, then upload again
Stuck on “Connecting…” Board is not in upload mode Hold the BOOT button, press and release RST, then release BOOT once uploading starts
Serial Monitor shows nothing Wrong baud rate, or the sketch printed before the monitor opened Set the Serial Monitor to 115200 baud, then press the RST button
PSRAM size shows 0.0 MB PSRAM is set to Disabled Tools → PSRAM → OPI PSRAM, then upload again
Wi-Fi scan finds no networks No 2.4 GHz network in range This board scans 2.4 GHz only. Move closer to a 2.4 GHz router

Spotted a problem in this tutorial? Email support@epartners.co.nz and we'll check it and update the tutorial.

Good to know
  • GPIOs are 3.3 V only. Do not connect 5 V signals directly.
  • GPIO35, GPIO36 and GPIO37 are used by the Octal PSRAM on N16R8 modules and cannot be used for your own circuits. GPIO0, GPIO3, GPIO45 and GPIO46 are strapping pins that set boot behaviour.
  • The N16R8 module is rated for −40 °C to +65 °C ambient.

Video guide

Datasheet

Key figures from the manufacturer's datasheet for the ESP32-S3-WROOM-1 (N16R8), the module on this board.

ESP32-S3-WROOM-1-N16R8 module
Variant ESP32-S3-WROOM-1-N16R8
Processor Xtensa® dual-core 32-bit LX7 (with single precision FPU), up to 240 MHz
Flash 16 MB (Quad SPI)
PSRAM 8 MB (Octal SPI)
ROM / SRAM / RTC SRAM 384 KB / 512 KB / 16 KB
Wi-Fi IEEE 802.11 b/g/n, 2412–2484 MHz, up to 150 Mbps
Bluetooth Bluetooth LE: Bluetooth 5, Bluetooth mesh
GPIOs 36 (4 strapping); IO35, IO36, IO37 used by the Octal PSRAM
Operating voltage 3.0–3.6 V
Ambient temperature (N16R8) −40 °C to +65 °C
Module size (WROOM-1) 18.0 × 25.5 × 3.1 mm

Download the ESP32-S3-WROOM-1 datasheet (PDF, 1.2 MB)

▸ Preview the datasheet

If the preview does not load on your device, use the download link above.

Source: Espressif Systems, ESP32-S3-WROOM-1 & ESP32-S3-WROOM-1U Datasheet, version 1.8.

Resources

Which one should I choose?

Product Key difference Best for
This product (ESP32-S3 N16R8) ESP32-S3, 16 MB flash + 8 MB PSRAM, Bluetooth 5 LE only, two USB-C ports Larger firmware and data buffers, native USB
ESP32 Development Board 38Pins ESP32-WROOM-32, 4 MB flash, Bluetooth 4.2 (Classic + BLE), micro-USB Projects that need Classic Bluetooth

FAQ

▸ Does it support Classic Bluetooth?

No. The ESP32-S3 supports Bluetooth LE (Bluetooth 5 and Bluetooth mesh) only, according to the Espressif datasheet.

▸ Does it work on 5 GHz Wi-Fi?

No. Wi-Fi is 802.11 b/g/n on the 2.4 GHz band only.

▸ Which USB-C port should I use to upload code?

Use the port the board labels as the serial port. The other port is the ESP32-S3’s native USB (GPIO19 and GPIO20).

▸ Why can’t I use GPIO35, GPIO36 or GPIO37?

On N16R8 modules these pins connect to the 8 MB Octal PSRAM inside the module, so they are not available for other uses.

▸ Which Arduino IDE settings should I use?

Choose ESP32S3 Dev Module, Flash Size 16MB (128Mb) and PSRAM OPI PSRAM. The Tutorial above walks through each step.

Technical question about this part? Email support@epartners.co.nz with your board and wiring, and we'll help you get it working.

Shipping: $5.99 urban, $9.99 rural. Free shipping on orders of $100 or more.

Order by 10:30am (NZT), Monday to Friday, and we dispatch the same day. Orders placed after 10:30am, on weekends or on public holidays are dispatched the next business day.

Delivery usually takes 1–2 business days after dispatch (2–3 for rural addresses). See our Shipping Policy for full details.

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.

Recently viewed