A pack of 40 Dupont jumper wires, 20 cm long, with 2.54 mm (0.1") connector ends — choose female-to-female, female-to-male or male-to-male.
Use them to join a breadboard, a microcontroller board and plug-in modules without soldering. At 20 cm they reach across a breadboard or between parts that sit a hand-width apart.
Specifications
| Fit | |
|---|---|
| Connector type | Dupont, single-pin housing on each end |
| Pitch | 2.54 mm (0.1") — wires sit side by side on a standard header |
| Ends | Female to Female, Female to Male, or Male to Male (choose an option) |
| Pack | |
| Quantity | 40 wires |
| Length | 20 cm |
| Colours | Mixed rainbow colours, joined side by side in a ribbon strip — peel off single wires or groups as you need them |
Fits / works with
| Works with | Notes |
|---|---|
| Solderless breadboards (830-point, 400-hole) | Use a male end — it plugs straight into the 2.54 mm holes |
| Female headers — e.g. Arduino UNO pin sockets, female pin headers | Use a male end |
| Male pin headers — e.g. sensor modules, Raspberry Pi 40-pin GPIO header, male pin headers | Use a female end |
| 2.0 mm pitch headers | ✗ Not a match — these wires are made for 2.54 mm pitch |
In the box
- 40 × 20 cm Dupont jumper wires, in the type you choose (F-F, M-F or M-M)
Options
| Option | What is different | Choose it when |
|---|---|---|
| Female to Female | A socket on both ends | Joining two parts that both have male pins — e.g. a sensor module to a Raspberry Pi GPIO header |
| Female to Male | A socket on one end, a pin on the other | Joining a module's male pins to a breadboard or to Arduino UNO sockets |
| Male to Male | A pin on both ends | Links across a breadboard, or from a breadboard to Arduino UNO sockets |
- Pull a wire out by its plastic housing, not by the wire, so the crimp inside does not loosen.
- These are made for 2.54 mm (0.1") pitch. They will not sit properly on 2.0 mm pitch headers.
- Jumper wires are for low-voltage signals and small supply currents. Never use them for mains wiring, and use thicker wire for motors and other high-current loads.
Resources
Which one should I choose?
| Product | Key difference | Best for |
|---|---|---|
| This product — 40 pcs, 20 cm | 20 cm long; F-F, M-F or M-M | Parts placed further apart, or links that cross a breadboard |
| Breadboard Jumper Dupont Wire 40pcs - 10cm | 10 cm long; same three end types | Short, tidy links between parts that sit close together |
| Breadboard Dupont Jumper Wires (M-M) - 65pcs | 65 wires, male to male only | Breadboard-only wiring that needs many links |
FAQ
▸ Which type do I need for a breadboard and an Arduino UNO?
Male to Male. The breadboard holes and the Arduino UNO pin sockets are both female, so you need a pin on each end. For a module with male header pins, choose Female to Male.
▸ Do these fit the Raspberry Pi GPIO header?
Yes, with a female end. The Raspberry Pi 40-pin GPIO header has male pins at 2.54 mm pitch, so use Female to Female (to a module) or Female to Male (to a breadboard).
▸ Should I choose 10 cm or 20 cm?
Choose 20 cm when the two parts are more than a few centimetres apart or the wire has to cross a breadboard. Choose 10 cm for short, tidy links between parts that sit close together.
▸ Can I turn a Female to Female wire into a Female to Male one?
Yes. Push a short piece of 2.54 mm male pin header into one socket end and it works as a male end.
Technical question about this part? Email support@epartners.co.nz with your board and wiring, and we'll help you get it working.
Shipping: $5.99 urban, $9.99 rural. Free shipping on orders of $100 or more.
Order by 10:30am (NZT), Monday to Friday, and we dispatch the same day. Orders placed after 10:30am, on weekends or on public holidays are dispatched the next business day.
Delivery usually takes 1–2 business days after dispatch (2–3 for rural addresses). See our Shipping Policy for full details.